Click Here

We have encountered this great article relating to How to Install a Bathtub Yourself directly below on the internet and accepted it made good sense to discuss it with you in this article.

Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult project. If the old bathtub is easily available, the project can move quickly; if you have to open up a wall surface to eliminate the old tub and place the brand-new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is far better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new tub in your washroom if you have already purchased a brand-new bathtub and also don't need to alter the plan of your previous water pipelines.
Your devices and also product list need to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted access that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. Once the supply pipelines have been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

Suitable New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area between the tap and the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

Installing the Tub

Using both wood boards under its feet, place the bathtub in the needed placement. The wooden boards are practical in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the tub up until the spirit level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub as well as likewise examine the overflow outlet as well as the normal outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub should wait until the bathtub has been used a minimum of once as this will settle it into its last setting.

Preparing for the Installation

Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final placement.

Tiling Around the Bath tub

In the area where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a stiff seal, creating the water to permeate the wall in between the bathroom and the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly early if you do not take into consideration this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I was made aware of that article on Installing A Bathtub through an acquaintance on a different web address. I beg you take the time to distribute this post if you appreciated it. I praise you for your time. Kindly come by our site back soon.

Plumbing woes? We help.